oem-odm · B2B PROCUREMENT
Split Dye Hoodie Manufacturer: Fleece Dye Lines and QC
By Weavnora · Updated

Direct answer
What buyers need to know
Split dye hoodie manufacturer programs garment dye each sewn hoodie in two colours with a planned split line, usually on 320-420 GSM cotton fleece or French terry. Expect a line tolerance of 2-4 cm, shrinkage of 4-7%, 2-3 sample rounds of 10-15 days and 35-50 days for bulk. MOQ depends on style and fabric.
Split dye hoodie manufacturer programs garment dye each sewn hoodie in two colours with a planned split line, usually on 320-420 GSM cotton fleece or French terry. Expect a line tolerance of 2-4 cm, shrinkage of 4-7%, 2-3 sample rounds of 10-15 days and 35-50 days for bulk. MOQ depends on style and fabric.
A split dye hoodie is a strong statement piece: one half in a washed black, the other in a faded grey, or a hood in a contrast colour that runs down one side of the body. On fleece the effect looks rich because the heavy fabric holds deep colour. It is also much harder to produce than a split dye tee. A 400 GSM hoodie absorbs a lot of water, weighs several times more when wet and has hood, pocket, cuffs and hem that all need to land on the correct side of the line. This guide explains how a split dye hoodie manufacturer plans the layout, controls colour on fleece and checks quality before bulk.
What is a split dye hoodie manufacturer?
A split dye hoodie manufacturer is a garment factory that sews hoodies in prepared-for-dye cotton fleece or French terry and dyes each finished hoodie in two colours, one section at a time, so the garment shows a defined split through the body, hood, sleeves or pocket. The work covers fabric and rib preparation, folding and clamping, dye recipes, line control, drying and shrinkage. Typical programs use 320-420 GSM cotton fleece, hold the line within 2-4 cm and add 7-12 days to bulk for the two-stage dye.
How should the split be planned on a hoodie?
A hoodie has more parts than a tee, so the layout must be decided in detail:
- Body split. Vertical left and right halves are most common. The line usually runs through the centre front and back.
- Hood. Decide whether the hood follows the body split, is fully one colour, or is split along its centre seam.
- Kangaroo pocket. A vertical split runs through the pocket; decide whether that is acceptable or whether the pocket should be one colour.
- Sleeves and cuffs. Typically follow their body side, but cuffs and hem rib can be planned as a contrast.
- Drawcords and eyelets. Drawcords are usually added after dyeing to keep them clean.
Draw all these parts on the tech pack and give the split a measured tolerance. A line described only as "half and half" leaves too much room for interpretation.
Planning a two-colour dyed hoodie? Weavnora develops garment dyed and washed heavyweight hoodies and confirms split position, colours, rib match and shrinkage on a dyed sample before bulk. See our vintage wash hoodies page for the base styles and fabrics we work with, then request a quote with your style, fabric and quantities. MOQ depends on style and fabric, so we confirm it in your quote.
Split dye vs colour-block panels on hoodies: which option fits?
| Selection criteria | Garment split dye | Sewn colour-block panels |
|---|---|---|
| Line look | Soft, slightly irregular | Sharp, seam-defined |
| Line tolerance | 2-4 cm piece to piece | Fixed by pattern |
| Colour depth on fleece | Rich, vintage | Depends on dyed fabric |
| Shrinkage control | Harder, garment shrinks in bath | Easier, fabric pre-shrunk |
| Handling in production | Heavy wet garments, two baths | Extra cutting and sewing |
| Best for | Statement, hand-made looks | Clean, repeatable designs |
The trade-offs are character against repeatability. Garment split dye gives each hoodie a unique, hand-dyed line, which suits vintage and streetwear stories. Sewn panels repeat perfectly but look more technical. If you want both, a common approach is a sewn panel hoodie that is then garment dyed in one colour for a washed look.
Which fleece and rib work best?
Fleece choice decides how well the dye takes and how much the hoodie shrinks:
- 100% cotton fleece or French terry of 320-420 GSM dyes evenly with reactive or pigment dye. Polyester blends dye unevenly.
- Prepared-for-dye fabric that is scoured and free from optical brighteners.
- Rib in the same cotton composition so cuffs and hem take the same colour as the body.
- Cotton thread if you want stitching to follow the dye; polyester thread stays white.
French terry dries faster and handles the double dye better than brushed fleece, which can felt or pill during long dye cycles. Our French terry vs fleece hoodie fabric guide compares both, and the hoodie fleece GSM guide helps you choose a weight.
How much will a split dye hoodie shrink?
Two dye cycles plus tumble drying mean more shrinkage than a single garment dye. Typical figures are 4-7% in length and 3-6% in width, and rib can shrink at a different rate from the body. The factory should cut the pattern larger, then measure the hoodie after dyeing. Ask for a size check on dyed samples in at least two sizes. Our fleece fabric shrinkage guide explains typical ranges.
How do you control colour on heavy fleece?
- Approve lab dips for both colours on the actual fleece, not on jersey.
- Agree the maximum bleed zone where colours meet, often 2-3 cm on fleece.
- Ask how many hoodies go in each dye load and group bulk by dye lot.
- Test colourfastness to washing and rubbing, especially dark next to light.
- Check the inside of the hood and pocket bag, where dye can be patchy.
Our dip dye hoodie manufacturer guide shows how gradient dyes are handled on the same type of fabric.
What should you send for a quote?
- A tech pack sketch showing the split on body, hood, pocket and sleeves, with a measured tolerance.
- Both target colours as Pantone references or physical swatches.
- Fleece type and weight, rib and thread preferences.
- Any print or embroidery, and whether it goes on before or after dyeing.
- Quantities by colour combination and size, and your delivery window.
Prints are usually applied after dyeing so the colours stay true, while embroidery can go either way depending on the thread.
What should you check before approving bulk?
- Split position on body, hood and pocket against the tolerance.
- Colour of both sides against approved lab dips in daylight.
- Rib and thread colour matching each side as planned.
- Measurements after dyeing in several sizes.
- Hand feel after softening, with no hard or felted patches.
- Hardware such as eyelets free from rust or staining.
For the full development path, see our custom hoodie and sweatshirt manufacturing guide. If you prefer swirl patterns to a straight line, compare the tie dye hoodie manufacturer guide.
Split dye hoodie manufacturer: typical specs and key numbers
| Spec | Typical estimate range |
|---|---|
| Hoodie fleece weight | 320-420 GSM |
| Split line tolerance | 2-4 cm |
| Bleed zone on fleece | 2-3 cm |
| Length shrinkage after two dye cycles | 4-7% |
| Sample lead time per round | 10-15 days |
| Extra bulk time for two-colour dye | 7-12 days |
| Bulk production after approval | 35-50 days |
| MOQ (pcs per style and colour) | Depends on style and fabric; confirmed in your quote |
These are typical industry estimate ranges for planning, not quotes; confirm actual figures with your supplier for your fabric, quantity and destination.
Key takeaways
- A split dye hoodie manufacturer dyes each sewn fleece hoodie in two colours with a planned split.
- Plan the hood, pocket, cuffs and drawcords on the tech pack, not just the body.
- Use 100% cotton fleece or French terry and cotton rib so all parts take the dye.
- Allow 4-7% shrinkage from two dye cycles and measure after dyeing.
- Approve both lab dips on the real fleece and check split, colour and hand feel before bulk.
Request a split dye hoodie manufacturer quote
Ready to sample a split dye hoodie? Send your tech pack or reference images, fabric preference, colours and quantities through our quote request form. MOQ depends on style and fabric, so we confirm it in your quote together with sampling time, approval steps and an itemised price.
Buyer questions
Frequently asked questions
What is a split dye hoodie?
It is a hoodie dyed in two colours after sewing, usually split into left and right halves through the body and hood.
Which fabric works best for split dye hoodies?
100% cotton fleece or French terry of 320-420 GSM dyes evenly, with French terry handling double dye cycles slightly better.
Does split dyeing shrink a hoodie?
Yes. Two dye cycles usually shrink a hoodie 4-7% in length, so patterns are cut larger.
Can the hood be a different colour from the body?
Yes. The hood can follow the body split, be fully one colour, or be split down its centre seam.
What is the MOQ for split dye hoodies?
MOQ depends on style, fabric and colours, so we confirm it in your quote.
Start a sourcing conversation
Share quantity, target GSM, destination and sample requirements.
Start your RFQ →Email files to postmaster@weavnora.com.